NotDads
09-26-2007, 07:48 PM
Bike won 8 NHRA Wally's, the D6 2001 Summit National Championship. Also 6 track Championships at Mission Raceway Park.
Bike Coverage
http://www.nhra.com/2001/summit/div6/index.html
http://www.speedzonemagazine.com/zon...nbikezone.html
Chassis built on a 1979 KZ1000 LTD frame
-Kossman conversion backend
-Kossman 5/8" offset sprocket kit
-620 chain (new), full top guard
-front end lowered and raked to 41'
-re-enforced backbone
-seat section frame gussets and re-enforced
-aluminum fuel cell 1/2 gallon
-Marvick 6.5" magneisium 3 spoke rear wheel
-7" MT tire 70% left
-Spoked aluminum front wheel
-84 Ninja body
-single disc brake front and back
-Gremica master rear
-stock hydralic front
-Adjustable rear struts for height
-Aluminun wheelie bars 70"
-71 inch wheel base
-Tapered steering head bearings
-Air over air shifter
-steering damper
-leveled chassis and wheelie bars
-Quick 1/4 turn throttle,2 cable push-pull
-Gremica master cly
-Sealed high amp battery
-Lightened starter clutch hub
-Air clutch
-new rear axle bearings
-new front sprocket offset bearing
Engine
-1261cc 11.5-1 Wiesco piston kit in a sleeved KZ block
-Welded crank
-re-enforced main center cap
-Ape studs & nuts top and bottom
-windage tray on crank
-MTC oil pan flow trap gate
-Under cut 5 speed tranny
-ported 79 KZ1000 cly head, clearanced for cams
-420 lift Andrews cams
-Ape valve springs
-flow cut valves and seats (3 angle)
-33 smoothbore mikuni carbs
-Fresh air intake tube
-Vance & Hines header
-Blowby catch system out past rear wheel
-accel coils & 8.8 mm wires
-Dyna S ignition
-Dyna 400 2 step
-Stewart Warner Shift Light Tach, NEW, Blue LED's
-self starting
-Adjustable cam sprockets
ASKING 5200.00 OBO
Bike Coverage
http://www.nhra.com/2001/summit/div6/index.html
http://www.speedzonemagazine.com/zon...nbikezone.html
Chassis built on a 1979 KZ1000 LTD frame
-Kossman conversion backend
-Kossman 5/8" offset sprocket kit
-620 chain (new), full top guard
-front end lowered and raked to 41'
-re-enforced backbone
-seat section frame gussets and re-enforced
-aluminum fuel cell 1/2 gallon
-Marvick 6.5" magneisium 3 spoke rear wheel
-7" MT tire 70% left
-Spoked aluminum front wheel
-84 Ninja body
-single disc brake front and back
-Gremica master rear
-stock hydralic front
-Adjustable rear struts for height
-Aluminun wheelie bars 70"
-71 inch wheel base
-Tapered steering head bearings
-Air over air shifter
-steering damper
-leveled chassis and wheelie bars
-Quick 1/4 turn throttle,2 cable push-pull
-Gremica master cly
-Sealed high amp battery
-Lightened starter clutch hub
-Air clutch
-new rear axle bearings
-new front sprocket offset bearing
Engine
-1261cc 11.5-1 Wiesco piston kit in a sleeved KZ block
-Welded crank
-re-enforced main center cap
-Ape studs & nuts top and bottom
-windage tray on crank
-MTC oil pan flow trap gate
-Under cut 5 speed tranny
-ported 79 KZ1000 cly head, clearanced for cams
-420 lift Andrews cams
-Ape valve springs
-flow cut valves and seats (3 angle)
-33 smoothbore mikuni carbs
-Fresh air intake tube
-Vance & Hines header
-Blowby catch system out past rear wheel
-accel coils & 8.8 mm wires
-Dyna S ignition
-Dyna 400 2 step
-Stewart Warner Shift Light Tach, NEW, Blue LED's
-self starting
-Adjustable cam sprockets
ASKING 5200.00 OBO